Chief Consultant

Electricity Awareness

Why Load Shedding Happens in Pakistan: A Technical Explanation for Consumers

Published: 22 April 2026  |  Author: Chief Consultant Pakistan  |  Technical Editorial
اردو میں پڑھیں ←

Every year, at some point, millions of electricity consumers across Pakistan find themselves living with outages lasting anywhere from a few hours to well over half a day, depending on where they live. And every year, the same question comes up: why is this happening again? The honest answer is rarely simple, and it is almost never the single explanation that gets repeated in casual conversation. Load shedding in Pakistan is the result of several overlapping factors, some seasonal, some structural, and some financial, that combine in different proportions from one year to the next.

This article explains the real, technical causes behind load shedding in Pakistan in a way that stays useful no matter which year you happen to be reading it in. Rather than focusing only on a single season’s numbers, it walks through the five recurring factors that drive outages, using a specific period in 2026 as a concrete, real world example of how these factors actually play out on the ground.

Load shedding does not always mean Pakistan lacks the electricity generation capacity it needs. In most cases, the country’s installed capacity is well above demand on paper. What actually happens is that a combination of fuel shortages, water availability, transmission limitations, and cost pressures prevents that capacity from being fully used at any given moment.

What Load Shedding Actually Is

Load shedding is the deliberate, temporary disconnection of electricity supply to specific areas, carried out to bring total demand back in line with what can actually be supplied at that moment. It is implemented by Distribution Companies, commonly called DISCOs, under instructions from the National Transmission and Despatch Company, or NTDC, whenever the electricity being generated and successfully delivered falls short of what consumers are drawing from the grid.

It helps to separate two numbers that often get confused: installed generation capacity, and actually available capacity. Pakistan’s power system has, for several years now, carried an installed capacity well above 40,000 MW. But installed capacity only tells you what could theoretically be produced if every plant were running at full output with no constraints. Available capacity, the number that actually determines whether load shedding happens on a given day, depends on a much longer list of moving parts: fuel supply, water levels, plant maintenance schedules, and transmission capability. The gap between these two numbers is where load shedding lives.

The Five Recurring Causes of Load Shedding in Pakistan

1. Fuel Supply Shortages, Particularly Natural Gas and LNG

A significant share of Pakistan’s thermal electricity generation depends on natural gas and imported Liquefied Natural Gas, known as LNG. When domestic gas production runs below requirement and LNG cargo deliveries are delayed or reduced, gas fired power plants simply cannot run at their designed output, regardless of how much capacity they have on paper. This is one of the most common and most immediate causes of load shedding in any given period, because fuel shortages can appear quickly and are often tied to international shipping schedules and global LNG pricing rather than anything happening domestically.

A Real Example: April 2026

In April 2026, Pakistan required roughly 350 million cubic feet per day of RLNG to run its gas based power plants at full capacity, but supply had dropped to around 80 million cubic feet per day, less than a quarter of what was needed. Three major RLNG plants, Bhikki in Sheikhupura, Haveli Bahadur Shah in Jhang, and Balloki in Kasur, together representing well over 3,500 MW of capacity, were running far below their potential output as a direct result. Fresh LNG shipments were delayed, and the shortage eased only once new cargo deliveries arrived in early May.

2. Reduced Hydropower Due to Seasonal Water Levels

Hydropower makes up a substantial part of Pakistan’s generation mix, with Tarbela and Mangla among the largest contributors. Unlike thermal generation, hydropower output is directly tied to how much water is flowing into these reservoirs at any given time, which is itself governed by snowmelt, glacial melt, and seasonal rainfall patterns in the Indus basin. In the months before glacial melt picks up, typically late winter into early spring, water inflows can be low enough to meaningfully constrain hydropower output, particularly during evening peak hours when demand is highest and solar generation has already stopped for the day.

A Real Example: April 2026

In April 2026, Tarbela Dam recorded inflows of around 20,200 cusecs against outflows of only 8,000 cusecs, while Mangla Dam showed a similar pattern, with inflows of about 29,100 cusecs against outflows of 8,000 cusecs. This constrained hydropower output by close to 2,000 MW during peak night hours, contributing directly to the evening load shedding many consumers experienced most severely during that period. As is typical for this time of year, output recovered through May and June as rising temperatures increased glacial melt into the river system.

3. The Solar Evening Peak Problem

This is the newest and least understood of the five causes, and it is becoming more significant every year as rooftop solar adoption grows across Pakistan. During daylight hours, millions of solar installations generate electricity locally, which genuinely reduces demand on the national grid and helps ease pressure during the day. The complication appears after sunset. Solar generation stops abruptly, and all of those consumers switch back to drawing power from the grid at roughly the same time, creating a sharp, concentrated spike in demand commonly referred to as the evening peak. Pakistan’s grid infrastructure, built around a more gradual demand curve, is not naturally equipped to absorb such a fast intra day swing, which is a large part of why load shedding tends to be at its worst in the early evening hours, typically somewhere between 5 PM and 1 AM, exactly when solar output has stopped and the grid must supply everyone simultaneously.

4. Transmission Infrastructure Limitations

Even when electricity is available somewhere on the national grid, physical transmission constraints can prevent it from reaching consumers in another part of the country. Pakistan’s major generation capacity is concentrated toward the south, while some of the largest demand centres sit in central and northern Punjab. The transmission corridors that carry power northward, operated by NTDC, have a finite capacity, and when that capacity is already saturated, a power plant in the south genuinely cannot simply send its surplus output to a shortage area further north. This is why, at certain times, one region of the country can have a comfortable supply while another faces extended outages, even though the national totals might look balanced on paper.

5. The Rising Cost of Alternative Fuels

When gas based generation falls short, the system has to rely more heavily on costlier alternatives, most commonly furnace oil. The trouble is that furnace oil prices can rise sharply within a short period, driven by international oil markets and currency movements. Running furnace oil plants at full capacity around the clock to fully cover a shortfall would push generation costs, and eventually consumer tariffs, significantly higher through the Fuel Cost Adjustment that appears on every bill. To avoid passing that full cost directly onto consumers, authorities often choose controlled load management instead of running the most expensive plants at maximum output, which is a deliberate, if unpopular, trade off between higher bills and more outages.

A Real Example: April 2026

Furnace oil prices roughly doubled between February and April 2026, rising from around Rs 200,000 per ton to nearly Rs 400,000 per ton in just two months. Running furnace oil plants harder to compensate for the gas shortfall during this period would have driven generation costs, and by extension consumer bills, considerably higher, which was a significant factor behind the load management decisions made at the time.

How These Five Factors Interact

None of these causes operates entirely on its own. A gas shortage forces greater reliance on furnace oil, which raises costs and encourages more conservative load management. Low hydropower output during the evening peak compounds the solar evening peak problem, since both push demand onto the same thermal plants at exactly the same hours. Transmission limitations mean that even a national surplus can coexist with a regional shortage. Understanding load shedding in any given period means looking at how these five factors are combining at that particular moment, rather than assuming a single cause explains everything.

Typical Regional Patterns Consumers Should Expect

While exact figures shift from year to year, some patterns tend to repeat. Urban centres with lower technical and non-technical losses generally see shorter, more predictable outages, often in the range of a few hours a day during stressed periods. Rural areas, and areas with historically higher losses or theft rates, tend to see considerably longer outages, sometimes extending well beyond half the day. Regions further from major generation and transmission infrastructure are also more exposed to the transmission bottleneck problem described above. Knowing your own region’s typical pattern helps set realistic expectations rather than reacting to every outage as an unexplained failure.

What Steps Typically Help Ease the Pressure

Across past periods of severe load shedding, a recurring set of measures has tended to bring relief, even if the exact timeline varies:

  • Fresh LNG cargo deliveries restoring gas supply to thermal plants closer to their designed capacity
  • Seasonal increases in water inflows as temperatures rise, restoring hydropower output through the summer months
  • Battery storage and grid modernisation investments aimed specifically at absorbing the solar evening peak more smoothly
  • Transmission capacity upgrades that gradually reduce the north south bottleneck over time

These are structural, longer term fixes rather than something that changes overnight, which is why load shedding tends to follow a recognisable seasonal rhythm rather than disappearing suddenly.

How Consumers Can Genuinely Help

Every electricity consumer has some influence, individually small but collectively meaningful, over how much pressure the grid experiences during stressed periods. The following actions consistently make a real difference:

  • Shift heavy appliance use to daytime hours. Running washing machines, irons, and water heaters between roughly 10 AM and 4 PM takes advantage of solar generation on the grid rather than adding to the evening peak.
  • Reduce unnecessary load during the peak window. Switching off lights and fans that are not in use, particularly between 6 PM and 11 PM, eases pressure during the hours load shedding is most likely to occur.
  • Set air conditioning to a higher temperature. Each degree lower than necessary meaningfully increases consumption, especially across many households simultaneously during summer.
  • Pay electricity bills on time. Unpaid bills contribute directly to circular debt, which limits the funds available for fuel purchases and directly affects how much generation capacity can actually be run.
  • Consider solar with battery storage, not solar alone. A system with battery backup reduces dependence on the grid specifically during the evening peak, rather than only during daylight hours.
  • Report electricity theft in your area. Theft and unbilled consumption remain a leading contributor to the especially long outages seen in some localities.
A practical way to think about it: load shedding severity in any given month is essentially a snapshot of how these five factors are lining up at that moment. A dry spring with a gas shortfall will almost always look worse than a wet summer with stable LNG supply, regardless of what changes in policy or infrastructure.

Key Takeaways

  • Load shedding rarely comes from a single cause. Fuel shortages, low hydropower, the solar evening peak, transmission limits, and rising fuel costs usually combine in different proportions each year.
  • Pakistan generally has enough installed capacity on paper. The real constraint is almost always how much of that capacity can actually be operated at a given moment.
  • The evening hours are consistently the most exposed. Solar generation stopping at sunset, combined with reduced hydropower at night, concentrates pressure into a narrow evening window.
  • Regional differences are normal, not a sign of unfairness on their own. Transmission bottlenecks mean supply and shortage can genuinely coexist in different parts of the same national grid.
  • Consumer behaviour has a real, measurable effect at scale. Shifting heavy loads to daytime hours and reducing evening peak usage are the most consistently effective actions an individual household can take.
Scroll to Top